Posts

Choke Self-Resonance

Image
  Choke Self-Resonance Filed in homebrew on May.28, 2011 In troubleshooting the matching network for my 43′ vertical antenna, I discovered that somewhere along the way, the RF-blocking choke in the matching network had overheated and melted all of its insulation off, shorting all of the turns together.  I suspect that this was caused by the wiring errors I discovered earlier, but I did find references ( here ) on the internet saying that the 100 uh chokes from Radio Shack have some series self-resonance that cause them to leak RF through at certain frequencies. I read elsewhere (don’t remember where) that removing the top layer of the coil can improve things a bit.  So I re-wound the coil with just one layer of windings, resulting in a 50 uh coil, rather than 100 uh.  The following experiment shows that the new coil does not appear to have any significant self-resonance between 1.5 and 30 mhz.  However, I’m not sure the 50 uh is going to give eno...

T-Bias interface

Image
  T-Bias interface Filed in Antennas on May.28, 2011 I had a comment a few weeks ago asking for more details about the T-Bias device used to send DC over the active RF coax to my 43′ vertical antenna. This is used to switch the matching network such that: 0 volts = 60 – 6 meter operation +12 volts = 80 meter operation -12 volts = 160 meter operation I based the design on the one from Phil, AD5X, on his website: http://www.ad5x.com/images/Articles/RemoteDC.pdf Here is my design:   T-Bias schematic The photo shows that I used the parallel capacitors to get the 0.03 uf feedthrough capacitance.  The RF choke is a Radio Shack 100 uh standard choke.   T-Bias (Shack End) Here you can see how I kept the 12 volt input from the wall wart isolated from the chassis, allowing me to use the switch to flip polarity as needed. I mounted the connector on a piece of fiberglass circuit board (no copper).  Then I riveted the fiberglass to the chassis. 12 volt...

WAS Progress from the Ranch

Image
  WAS Progress from the Ranch Filed in Contests on Apr.29, 2011 I’ve been working on a Worked All States Award from the Ranch.  All contacts for WAS must be made with your station within a 50 mile radius  to count towards the WAS award, so only contacts made from the Ranch, but not Mesa, count for this. Anyway, I have contacted all states from the Ranch, but have received confirmation from only 36 so far.  So each time I operate from the Ranch, I’ll have to keep my eye out for those that have not sent confirmations.   WAS Progress April 2011

Beginnings

Image
  Beginnings Filed in Vintage Radio on Apr.02, 2011 When I was about 11 or 12 years old, I had developed a pretty intense interest in radios.  Shortwave and Ham Radio were at the top, but pretty much any radio communications was just too cool to ignore. I came across this site today that brought back some early memories of those interests.  The site has most of the old Radio Shack catalogs from when I was growing up. RadioShack Catelogs Anyway, probably the first electronic kit I ever built was the RadioShack P-Box Regenerative Receiver.  I remember winding different coils to hook into the clip springs to make it tune all over the shortwave spectrum.   P-Box Regenerative Receiver There were several others that I built, including the 1-tube receiver, which took a 22 volt battery.   1 Tube Receiver Here is the original P-Box clipping, explaining how the system worked.   P-Box Pretty cool stuff…

WAS (Worked All States) from the Ranch

Image
  WAS (Worked All States) from the Ranch Filed in Contests on Mar.24, 2011   QSL Finished Product I’ve been a ham since 1976, and never gone through the trouble of collecting the cards to apply for a Worked All States Award. While I was at the ranch in March, I was tuning around 80 meters and came across the Geratol Net on 3.668 Mhz.  This is a WAS net, with the main purpose being to increase activity in the Extra Class band segment of 80 meters.  I found myself logging in and participating on the next 3 nights.  Hey, it beats going to bed early when it’s dark. Anyway, I worked 30 states in 3 days, and combined with what I have logged over the last two years at the Ranch during Field Day, I have worked all states from there.  I don’t have confirmations from everywhere yet, though.  It may take a few more trips to gather the required cards, but it should be pretty easy. I was surprised at the area easily covered by 80 meters with an anten...

Portable Power

Image
  Portable Power Filed in Station on Mar.23, 2011 I like operating from the Ranch, because I have some decent antennas there, and the background noise is nearly nonexistent.  But in the past, that has involved packing all my radio stuff up, including the old Astron 20-Amp linear power supply (= heavy). I decided to make things a little more convenient.  I got a 115 amp-hour marine battery from Walmart, and a cheap 2amp/6amp battery charger from Harbor Freight.   Harbor Freight Charger With these hooked up at the ranch, I can now have the battery charging while the generator is running for other stuff (like construction or cooking).  Then I can turn the generator off and run off battery for a long time.  It’s really nice at night, when I can set the TS-480 up to automatically shut off after 60 minutes (or 120, or 180).  That allows me to go to bed listening to the gents on 80 meters or 160 meters, and not have to worry about running dow...

Quick Disconnect for Doublet Antenna

Image
  Quick Disconnect for Doublet Antenna Filed in Antennas on Mar.23, 2011 To finish the job we started in January, I got a 2″x4″ weathertight plastic electrical box from Home Depot.  This was used to mount a permanent set of banana jacks to the house so the doublet could be quickly attached or detached.   Doublet Disconnect To make the box ready, I cut two slots in the hole on the bottom to allow the ladder line to pass easily into it.   Slots in Electrical Box Next, I passed the window line through the slots to make sure it fit.   Window Line in box After that, I mounted the box to the side of the house with some 1-1/2″ screws to the trim.  The window line was fitted with ring terminals and attached to the two banana jacks on the inside.   Connections Finally, a snap ring was attached to a loop of rope to serve as a strain relief.  This is easily snapped to the eye ring at the bottom of the box.  It works pretty well.  ...